Fuel and air code
P0103: Mass airflow sensor reads too high
How much to fix P0103? Typically $120–$390.
How this range is built
| Part of the job | Low | High |
|---|---|---|
| Parts | $70 | $250 |
| Labor: 0.5 to 0.8 hours × $110 to $150 an hour | $55 | $120 |
| Fees: shop supplies, disposal, diagnostics | $0 | $15 |
| Total, rounded | $120 | $390 |
The hourly rate is the BLS Occupational Employment and Wage Statistics, May 2025 average pay for this trade in the US, $27.13 an hour, times 4 to 5.5 to cover what a shop bills (overhead, tools, insurance, profit). Parts are a band from budget aftermarket to the manufacturer part. Full method.
Not a repair shop, estimates only. Typical range, estimate. Not a quote. Your car, parts and shop change the number.
This is the range for the most common fix, mass airflow sensor replacement. Which repair your car needs depends on a proper diagnosis.
The mass airflow sensor tells the computer how much air is entering the engine. This code means the sensor reports far more air than the engine could be taking in. The computer then adds too much fuel, so the mix runs rich with black smoke and poor mileage.
- Safe to drive?
- Short trips only
- Most common cause
- Dirty or failed MAF sensor
Drive gently. Mileage and idle quality suffer.
Get quotes from local shops
Got P0103? Tell us your ZIP and a shop near you can quote the repair. Free, takes a minute.
Fair Price is not a contractor or a repair shop. Who sees your request
What you may notice
- Rough idle
- Black smoke from the tailpipe
- Poor fuel economy
- Hesitation when accelerating
Common causes, most likely first
- Dirty or failed MAF sensor
- Air leak after the sensor
- Wiring fault
- Clogged air filter
Check this first
Check the air filter and clean the sensor with a spray made for MAF sensors, letting it dry fully. Also check the plug for loose pins or corrosion, since a shorted signal can read high too.
Other repairs that sometimes fix P0103
| Repair | Typical range, US |
|---|---|
| Vacuum leak repair | $90 to $460 |
| Diagnostic scan (check engine light) | $55 to $250 |
Before you pay
- Ask the shop what test showed this part is the cause, not just that the code appeared.
- Ask for parts and labor listed separately, and for the hours.
- Ask for a written OK before any extra work. Many states require written authorization before repairs.
Got a quote already? Check it against the range. Want to see if your car has a recall tied to this problem? Check recalls by VIN.
Need to read a code yourself? OBD-II scanners on eBay (affiliate link, disclosure).
P0103 questions
Can I clean it?
Yes, with a MAF-safe spray. Do not touch the sensor wire or use general cleaners, and let it dry before reinstalling. If the code returns soon, the sensor may need replacement.
Is the filter a cause?
A dirty filter can skew the reading by letting dust or debris coat the sensor, though it more often causes a low-air code. It is cheap to replace, so rule it out.
Cost?
Moderate for most cars, but some brands charge much more for the part. Confirm the diagnosis first, and ask whether a cleaning or a wiring check was done before the part was ordered.
How much does it cost to fix P0103?
The most common fix, mass airflow sensor replacement, has a typical range of $120 to $390 across the US. It is an estimate built from parts prices and local labor wages, not a quote. Your car and shop change it.
Typical range in 10 metro areas
Only the labor rate changes between cities. Same parts, same hours.
| Area | Typical range, estimate |
|---|---|
| Boston area, Massachusetts | $130 to $410 |
| New York City area | $130 to $400 |
| Los Angeles area, California | $130 to $410 |
| Chicago area, Illinois | $120 to $390 |
| Houston area, Texas | $120 to $390 |
| Dallas-Fort Worth area, Texas | $120 to $390 |
| Phoenix area, Arizona | $120 to $390 |
| Atlanta area, Georgia | $120 to $390 |
| Miami area, Florida | $120 to $390 |
| Seattle area, Washington | $130 to $410 |
Related codes
- P0101: Air flow sensor reading seems off
- P0102: Air flow sensor signal too low
- P0171: Engine getting too much air or too little fuel (bank 1)
More fuel and air codes
Code meaning written in our own words. Some codes mean different things on different makes, so check your scan tool or manual. Not a repair shop, estimates only.